Safety Equipment for the Glass Industry

All Products

Items 1 to 10 of 18 total

per page
Page:
  1. 1
  2. 2

List  Grid 

Set Descending Direction
  1. Banom® Level4® 4005 Glove Cut Resistant Cut Level 4 - 6 Dozen Case

    Banom® Level4® 4005 Glove Cut Resistant Cut Level 4 - 6 Dozen Case

    6 Dozen Case at $6.97 a pair.

    Banom® Level4® gloves are designed for use in areas where shop knives are being used for wire splicing. The special neoprene coated palm gives a positive grip in oily, wet, or dry applications. These gloves are flexible and comfortable to wear and are ideal for use in outdoor applications by telephone, cable, and utility workers. Learn More
  2. Banom® 4005 Glove Cut Resistant - ANSI Cut Level4® - Dozen

    Banom® 4005 Glove Cut Resistant - ANSI Cut Level4® - Dozen

    1 Dozen Pack at $7.12 a pair.

    Banom® Level4® gloves are designed for use in areas where shop knives are being used for wire splicing. The special neoprene coated palm gives a positive grip in oily, wet, or dry applications. These gloves are flexible and comfortable to wear and are ideal for use in outdoor applications by telephone, cable, and utility workers. Learn More
  3. Banom® TriMax® 4200 Glove - ANSI Cut Level 4 - 12 Each Pack

    Banom® TriMax® 4200 Glove - ANSI Cut Level 4 - 12 Each Pack

    12 Pack at $8.81 each.

    TriMax® is our lightest weight and most popular cut-resistant liner. Each glove is knit with two strands of cut-resistant yarn instead of one. If the first strand fails, the second is there as a backup. These liners are extremely light weight so they can be comfortably worn underneath cover gloves. These gloves are made entirely of FDA accepted materials required by USDA for food use and contain AlphaSan®, a permanent antimicrobial that kills bacteria, fungus, mold, and mildew. Applications include food processing and food service where cut-resistant liners are worn underneath cover gloves. When handling glass, these liners can be used for additional cut protection. Learn More
  4. Banom® PowerPlus™ - Dynamax® 45 with Foam Nitrile Coating Palm coated knitwrist - ANSI Cut Level 4 - 6 Dozen Case

    Banom® PowerPlus™ - Dynamax® 45 with Foam Nitrile Coating Palm coated knitwrist - ANSI Cut Level 4 - 6 Dozen Case

    6 Dozen Case at $6.88 a pair.

    PowerPlus™ gloves provide a positive grip in sheet metal stamping and press operations where hydrocarbon-based lubricants are being used. PowerPlus™ gloves are made with Dynamax® 45, a continuous filament yarn that combines ultra high tensile strength with a yarn hardness which allows this product to resist the cutting edges of sheet metal, machined metal, glass, and knife blades. The special palm coating on both gloves absorbs lubricants for an increased grip without allowing liquids to penetrate to the hands. Due to their tacky grip, these gloves are not recommended for use when turning nuts, bolts, or screws with a power tool as this can result in a “wrap-up”. Nitrile coatings can become slippery in water-based solutions. These gloves are made with a synthetic yarn, so they should not be used near heat or open flame. PowerPlus™gloves should be edge-tested prior to approval for use. Learn More
  5. Banom® AquaPlus™ - Dynamax® 45 with Textured Latex Palm Coating - ANSI Level 4 - Dozen

    Banom® AquaPlus™ - Dynamax® 45 with Textured Latex Palm Coating - ANSI Level 4 - Dozen

    1 Dozen Pack at $7.64 a pair.

    AquaPlus™ gloves are specifically designed to handle wet glass. They can also be used in any water-based solution that causes flat metal or glass surfaces to be slippery. The dimpled texture of the latex palm coating creates a suction that gives a positive grip when handling wet surfaces. Natural rubber also provides abrasion, cut, and puncture resistance. AquaPlus™ gloves are made with Dynamax® 45, a continuous filament yarn that combines ultra high tensile strength with a yarn hardness, which allows this product to resist the cutting edges of sheet glass and knife blades. AquaPlus™ gloves have extended length knitwrist cuffs that add protection to the wrist area where arteries, tendons, and nerves are vulnerable to lacerations. The new Taperfit® wrist design allows a contoured fit without tightness or discomfort. These gloves have a latex palm coating. Natural rubber can cause an allergic reaction in some individuals. Due to their tacky grip, these gloves are not recommended for use when turning nuts, bolts, or screws with a power tool as this can result in a “wrap-up”. These gloves are made with a synthetic yarn, so they should not be used near heat or open flame. AquaPlus™ gloves should be edge-tested prior to approval for use. Learn More
  6. Banom® DuraPlus® 2805 - Dynamax® 45 with Bi-Polymer Coating - ANSI Cut Level 4 - Case

    Banom® DuraPlus® 2805 - Dynamax® 45 with Bi-Polymer Coating - ANSI Cut Level 4 - Case

    6 Dozen Case at $6.36 a pair.

    Banom® DuraPlus® 2805 - Dynamax® 45 with Bi-Polymer Coating - ANSI Cut Level 4 Learn More
  7. Banom® Flash 'n Slash® - ANSI Cut Level 4 - Dozen

    Banom® Flash 'n Slash® - ANSI Cut Level 4 - Dozen

    1 Dozen Pack at $10.38 a pair.

    Flash 'n Slash® gloves and sleeves are designed for cut resistance in sheet metal, glass and knife blade hazards where there is a potential exposure to heat, sparks, and open flame. These products are made with Fyron 45, a continuous filament yarn that combines ultra high tensile strength with a yarn hardness that allows this product line to resist the cutting edges of sheet metal, machined metal, glass, and knife blades. This yarn and the special palm coating used in style DP-6705 are inherently flame resistant. Flash 'n Slash gloves and sleeves are 100% latex free. Due to their tacky grip, style DP-6705 gloves are not recommended for use when turning nuts, bolts, and screws with a power tool as this can result in a "wrap-up." Flash 'n Slash gloves and sleeves should be edge-tested prior to approval for use. Learn More
  8. Banom® Flex4® 6506 - ANSI Level 4 - Polyurethane Palm Coating on Dynamax®45 Glove Liner - 6 Dozen Case

    Banom® Flex4® 6506 - ANSI Level 4 - Polyurethane Palm Coating on Dynamax®45 Glove Liner - 6 Dozen Case

    6 Dozen Case at $8.95 a pair.

    Banom® Flex4® 6506 - ANSI Level 4 - Polyurethane Palm Coating on Dynamax®45 Glove Liner Learn More
  9. Banom® Flex4® 6505 - ANSI Level 4 - Polyurethane Palm Coating on Dynamax®45 Glove Liner - Dozen

    Banom® Flex4® 6505 - ANSI Level 4 - Polyurethane Palm Coating on Dynamax®45 Glove Liner - Dozen

    1 Dozen Pack at $6.19 a pair.

    Banom® Flex4® 6505 - ANSI Level 4 - Polyurethane Palm Coating on Dynamax®45 Glove Liner Learn More
  10. Banom® PowerPlus™ - Dynamax® 45 with Foam Nitrile Coating Palm coated knitwrist - ANSI Cut Level 4 - Dozen

    Banom® PowerPlus™ - Dynamax® 45 with Foam Nitrile Coating Palm coated knitwrist - ANSI Cut Level 4 - Dozen

    1 Dozen Pack at $6.88 a pair.

    PowerPlus™ gloves provide a positive grip in sheet metal stamping and press operations where hydrocarbon-based lubricants are being used. PowerPlus™ gloves are made with Dynamax® 45, a continuous filament yarn that combines ultra high tensile strength with a yarn hardness which allows this product to resist the cutting edges of sheet metal, machined metal, glass, and knife blades. The special palm coating on both gloves absorbs lubricants for an increased grip without allowing liquids to penetrate to the hands. Due to their tacky grip, these gloves are not recommended for use when turning nuts, bolts, or screws with a power tool as this can result in a “wrap-up”. Nitrile coatings can become slippery in water-based solutions. These gloves are made with a synthetic yarn, so they should not be used near heat or open flame. PowerPlus™gloves should be edge-tested prior to approval for use. Learn More

Items 1 to 10 of 18 total

per page
Page:
  1. 1
  2. 2

List  Grid 

Set Descending Direction