Safety Equipment for the Glass Industry

All Products

Items 1 to 10 of 12 total

per page
Page:
  1. 1
  2. 2

List  Grid 

Set Descending Direction
  1. Banom® Protectall™ 3200 Glove - ANSI Cut Level 2 - 6 Dozen Case

    Banom® Protectall™ 3200 Glove - ANSI Cut Level 2 - 6 Dozen Case

    6 Dozen Case at $7.41 a pair.

    Protectall™ gloves are designed to fit either hand comfortably. The MaxPly® Dyneema® liner provides ANSI Level 2 cut protection. The special foam pads add cushioning in areas of the hand that need protection from impact, vibration, and finger tip pinch points. This patented pattern allows hand flexion without restriction and contours to the knuckles on the back of the hand. The new Taperfit® wrist design allows a contoured fit without tightness or discomfort and covers the area of the wrist where arteries, tendons, and nerves are vulverable to lacerations. These gloves are cool and comfortable to wear, ambidextrous for extended use, and can be cleaned with the Bantex® process to reduce average unit cost. Learn More
  2. Banom® Protectall™ 3200 Glove - ANSI Cut Level 2 - Dozen

    Banom® Protectall™ 3200 Glove - ANSI Cut Level 2 - Dozen

    1 Dozen Pack at $7.56 a pair.

    Protectall™ gloves are designed to fit either hand comfortably. The MaxPly® Dyneema® liner provides ANSI Level 2 cut protection. The special foam pads add cushioning in areas of the hand that need protection from impact, vibration, and finger tip pinch points. This patented pattern allows hand flexion without restriction and contours to the knuckles on the back of the hand. The new Taperfit® wrist design allows a contoured fit without tightness or discomfort and covers the area of the wrist where arteries, tendons, and nerves are vulverable to lacerations. These gloves are cool and comfortable to wear, ambidextrous for extended use, and can be cleaned with the Bantex® process to reduce average unit cost. Learn More
  3. Banom® Duralite®HV- DuraPlate® 2206 Glove with Polyurethane Palm Coating and Back of Hand Impact Protection- ANSI Cut Level 2 - 6 Dozen Case

    Banom® Duralite®HV- DuraPlate® 2206 Glove with Polyurethane Palm Coating and Back of Hand Impact Protection- ANSI Cut Level 2 - 6 Dozen Case

    6 Dozen Case at $7.18 a pair.

    Duralite® HV gloves offer high visibility orange and yellow colors with back of hand impact protection. These gloves are designed for both outdoor and indoor use in sheet metal handling and assembly, electrical wiring, and dry wall installation. The continuous filament DuraPlate® yarn resists sheet metal edges and provides good abrasion resistance. The special palm coating provides a good grip in oily, wet or dry applications. The Taperfit® wrist design is extended length and allows a contoured fit without tightness or discomfort. Learn More
  4. Banom® Traxx® 3306 Glove - ANSI Cut Level 4 - Dozen

    Banom® Traxx® 3306 Glove - ANSI Cut Level 4 - Dozen

    1 Dozen Pack at $8.27 a pair.

    Mechanics and maintenance professionals need gloves with dexterity that grip well in oily applications. Even with the best grip, hands can slip causing bruises and contusions on the knuckles and the back of the fingers and hands. Traxx® gloves are designed with a palm coating that provides a positive grip in oily, wet, or dry applications. If hands should slip, Traxx® gloves have padded chevrons to reduce the severity of a "knuckle busting" accident. Knit with ArmorPlate Traxx® gloves provide cut and abrasion protection in a wide variety of situations. Learn More
  5. Banom® ArmorFit™ 9505 Glove - Light Weight ArmorPlate™ with Polyurethane Palm Coating - ANSI Cut Level 2 - Dozen

    Banom® ArmorFit™ 9505 Glove - Light Weight ArmorPlate™ with Polyurethane Palm Coating - ANSI Cut Level 2 - Dozen

    1 Dozen Pack at $7.38 a pair.

    ArmorFit™™ gloves are the lightest weight gloves that we offer. They provide maximum dexterity and tactile feel and are designed to give a broad range of protection in multiple cut hazards particularly in fine assembly. ArmorFit™™ gloves are 100% latex free. The Taperfit® knitwrist cuffs are extended length to protect the wrist area. These gloves have been treated with Sanifresh® to prevent bacteria from growing both during and after glove use. ArmorFit™™ gloves may be cleaned repeatedly with the Bantex® cleaning process.Polyurethane coatings offer the most comfort and dexterity but provide the least abrasion and puncture resistance as compared to nitrile or latex coatings. All gloves should be application tested in the environment in which they are intended to be used. Learn More
  6. Banom® Flash 'n Slash® - ANSI Cut Level 4 - 6 Dozen Case

    Banom® Flash 'n Slash® - ANSI Cut Level 4 - 6 Dozen Case

    6 Dozen Case at $9.56 a pair.

    Flash 'n Slash® gloves and sleeves are designed for cut resistance in sheet metal, glass and knife blade hazards where there is a potential exposure to heat, sparks, and open flame. These products are made with Fyron 45, a continuous filament yarn that combines ultra high tensile strength with a yarn hardness that allows this product line to resist the cutting edges of sheet metal, machined metal, glass, and knife blades. This yarn and the special palm coating used in style 6705 are inherently flame resistant. Flash 'n Slash gloves and sleeves are 100% latex free. Due to their tacky grip, style 6705 gloves are not recommended for use when turning nuts, bolts, and screws with a power tool as this can result in a "wrap-up." Flash 'n Slash gloves and sleeves should be edge-tested prior to approval for use. Learn More
  7. Banom® Duralite®HV- DuraPlate® Glove with Polyurethane Palm Coating and Back of Hand Impact Protection- ANSI Cut Level 2 - Dozen

    Banom® Duralite®HV- DuraPlate® Glove with Polyurethane Palm Coating and Back of Hand Impact Protection- ANSI Cut Level 2 - Dozen

    1 Dozen Pack at $7.33 a pair.

    Duralite® HV gloves offer high visibility orange and yellow colors with back of hand impact protection. These gloves are designed for both outdoor and indoor use in sheet metal handling and assembly, electrical wiring, and dry wall installation. The continuous filament DuraPlate® yarn resists sheet metal edges and provides good abrasion resistance. The special palm coating provides a good grip in oily, wet or dry applications. The Taperfit® wrist design is extended length and allows a contoured fit without tightness or discomfort. Learn More
  8. Banom® PowerPlus™ - Dynamax® 45 with Foam Nitrile Coating Palm coated knitwrist - ANSI Cut Level 4 - 6 Dozen Case

    Banom® PowerPlus™ - Dynamax® 45 with Foam Nitrile Coating Palm coated knitwrist - ANSI Cut Level 4 - 6 Dozen Case

    6 Dozen Case at $6.88 a pair.

    PowerPlus™ gloves provide a positive grip in sheet metal stamping and press operations where hydrocarbon-based lubricants are being used. PowerPlus™ gloves are made with Dynamax® 45, a continuous filament yarn that combines ultra high tensile strength with a yarn hardness which allows this product to resist the cutting edges of sheet metal, machined metal, glass, and knife blades. The special palm coating on both gloves absorbs lubricants for an increased grip without allowing liquids to penetrate to the hands. Due to their tacky grip, these gloves are not recommended for use when turning nuts, bolts, or screws with a power tool as this can result in a “wrap-up”. Nitrile coatings can become slippery in water-based solutions. These gloves are made with a synthetic yarn, so they should not be used near heat or open flame. PowerPlus™gloves should be edge-tested prior to approval for use. Learn More
  9. Banom® Traxx® 3306 Glove - ANSI Cut Level 4 - Case

    Banom® Traxx® 3306 Glove - ANSI Cut Level 4 - Case

    6 Dozen Case at $8.12 a pair.

    Mechanics and maintenance professionals need gloves with dexterity that grip well in oily applications. Even with the best grip, hands can slip causing bruises and contusions on the knuckles and the back of the fingers and hands. Traxx® gloves are designed with a palm coating that provides a positive grip in oily, wet, or dry applications. If hands should slip, Traxx® gloves have padded chevrons to reduce the severity of a "knuckle busting" accident. Knit with ArmorPlate Traxx® gloves provide cut and abrasion protection in a wide variety of situations. Learn More
  10. Banom® Flash 'n Slash® - ANSI Cut Level 4 - Dozen

    Banom® Flash 'n Slash® - ANSI Cut Level 4 - Dozen

    1 Dozen Pack at $10.38 a pair.

    Flash 'n Slash® gloves and sleeves are designed for cut resistance in sheet metal, glass and knife blade hazards where there is a potential exposure to heat, sparks, and open flame. These products are made with Fyron 45, a continuous filament yarn that combines ultra high tensile strength with a yarn hardness that allows this product line to resist the cutting edges of sheet metal, machined metal, glass, and knife blades. This yarn and the special palm coating used in style DP-6705 are inherently flame resistant. Flash 'n Slash gloves and sleeves are 100% latex free. Due to their tacky grip, style DP-6705 gloves are not recommended for use when turning nuts, bolts, and screws with a power tool as this can result in a "wrap-up." Flash 'n Slash gloves and sleeves should be edge-tested prior to approval for use. Learn More

Items 1 to 10 of 12 total

per page
Page:
  1. 1
  2. 2

List  Grid 

Set Descending Direction