Safety Equipment for the Glass Industry

All Products

Items 1 to 10 of 15 total

per page
Page:
  1. 1
  2. 2

List  Grid 

Set Descending Direction
  1. Banom® Thornblocker® 7450 Glove Liner - Blue Nitrile Coating on a 100% Kevlar® Plated Cotton Jersey - ANSI Cut Level 3 - Dozen

    Banom® Thornblocker® 7450 Glove Liner - Blue Nitrile Coating on a 100% Kevlar® Plated Cotton Jersey - ANSI Cut Level 3 - Dozen

    1 Dozen Pack at $9.06 a pair.

    74 Series gloves are designed for automotive stamping, steel strip manufacturing, and fabrication where hydrocarbon-based lubricants are present. The nitrile coating is abrasion, snag, and oil resistant, while the Kevlar® plated cotton liner provides cut resistance on both palm side and back of the hand. Though less flexible than seamless knit lined gloves, these styles are extremely durable in abrasive cut hazard applications. Learn More
  2. Magnum® - Dynamax® HD with Leather Palm - ANSI/ISEA 105-2016 Cut Level A3

    Magnum® - Dynamax® HD with Leather Palm - ANSI/ISEA 105-2016 Cut Level A3

    1 Dozen Pack at $9.58 a pair.

    Magnum® - Dynamax® HD with Leather Palm - ANSI/ISEA 105-2016 Cut Level A3 Magnum® gloves provide higher cut hazard protection in sheet metal applications that require a leather palm for positive grip and abrasion resistance. Style 6305 Magnum® gloves are knit with four strands of Dynamax® HD continuous filament yarn for a total tensile strength of 672 Newtons. Tensile strength is needed to resist the burrs on stamped, punched, or pressed sheet metal edges. These gloves are made with a synthetic yarn, so they should not be used near heat or open flame. They are not recommended for use in applications where nuts, bolts, or screws are being turned with a power tool as a metal flashing could trap in the knit cloth and cause a "wrap-up." Magnum® 6305 gloves should be edge-tested prior to approval for use. Learn More
  3. Banom® 7712 Hand Pad ANSI Cut Level 3 - 12 Each Pack

    Banom® 7712 Hand Pad ANSI Cut Level 3 - 12 Each Pack

    12 Pack at $0.74 each.

    Banom® 7712 Hand Pad Learn More
  4. Banom® Abratex® 7712 Glove Cotton Terrycloth with Duralon® Reinforced Thumb Crotch - ANSI Cut Level 3 - 3 Dozen Case

    Banom® Abratex® 7712 Glove Cotton Terrycloth with Duralon® Reinforced Thumb Crotch - ANSI Cut Level 3 - 3 Dozen Case

    3 Dozen Case at $2.36 a pair.

    Banom® These terrycloth gloves are designed for stamping and sheet metal fabrication operations where punched metal parts are oily. The gloves feature a continuous cuff for added protection to the wrist area. Full Duralon® reinforcement along thumb and index finger increases durability in the area of the glove most subject to wear. Cotton loops provide a good grip on oily surfaces, Abratex® yarn in loop resists cuts from metal edges. Gloves are gray in color to aid in reconditioning. The cuffs are color coded for easy size identification. A full size range ensures a proper fit. Learn More
  5. Banom® Thornblocker® 7450 Glove Liner - Blue Nitrile Coating on a 100% Kevlar® Plated Cotton Jersey - ANSI Cut Level 3 - 6 Dozen Case

    Banom® Thornblocker® 7450 Glove Liner - Blue Nitrile Coating on a 100% Kevlar® Plated Cotton Jersey - ANSI Cut Level 3 - 6 Dozen Case

    6 Dozen Case at $8.91 a pair.

    74 Series gloves are designed for automotive stamping, steel strip manufacturing, and fabrication where hydrocarbon-based lubricants are present. The nitrile coating is abrasion, snag, and oil resistant, while the Kevlar® plated cotton liner provides cut resistance on both palm side and back of the hand. Though less flexible than seamless knit lined gloves, these styles are extremely durable in abrasive cut hazard applications. Learn More
  6. Magnum® - Dynamax® HD with Leather Palm - ANSI/ISEA 105-2016 Cut Level A3

    Magnum® - Dynamax® HD with Leather Palm - ANSI/ISEA 105-2016 Cut Level A3

    6 Dozen Case at $9.33 a pair.

    Magnum® - Dynamax® HD with Leather Palm - ANSI/ISEA 105-2016 Cut Level A3 Magnum® gloves provide higher cut hazard protection in sheet metal applications that require a leather palm for positive grip and abrasion resistance. Style 6305 Magnum® gloves are knit with four strands of Dynamax® HD continuous filament yarn for a total tensile strength of 672 Newtons. Tensile strength is needed to resist the burrs on stamped, punched, or pressed sheet metal edges. These gloves are made with a synthetic yarn, so they should not be used near heat or open flame. They are not recommended for use in applications where nuts, bolts, or screws are being turned with a power tool as a metal flashing could trap in the knit cloth and cause a "wrap-up." Magnum® 6305 gloves should be edge-tested prior to approval for use. Learn More
  7. Banom® Abratex® 7712 Glove Cotton Terrycloth with Duralon® Reinforced Thumb Crotch - ANSI Cut Level 3 - Dozen

    Banom® Abratex® 7712 Glove Cotton Terrycloth with Duralon® Reinforced Thumb Crotch - ANSI Cut Level 3 - Dozen

    1 Dozen Pack at $2.51 a pair.

    Banom® These terrycloth gloves are designed for stamping and sheet metal fabrication operations where punched metal parts are oily. The gloves feature a continuous cuff for added protection to the wrist area. Full Duralon® reinforcement along thumb and index finger increases durability in the area of the glove most subject to wear. Cotton loops provide a good grip on oily surfaces, Abratex® yarn in loop resists cuts from metal edges. Gloves are gray in color to aid in reconditioning. The cuffs are color coded for easy size identification. A full size range ensures a proper fit. Learn More
  8. Banom® Duramax® - 2305 Glove Liner with Synthetic BiPolymer Palm Coating on Dynamax® HD - ANSI Cut Level 2 - Dozen

    Banom® Duramax® - 2305 Glove Liner with Synthetic BiPolymer Palm Coating on Dynamax® HD - ANSI Cut Level 2 - Dozen

    1 Dozen Pack at $6.25 a pair.

    Duramax® - Synthetic BiPolymer Palm Coating on Dynamax® HD Liner - ANSI Cut Level 2 Learn More
  9. Banom® CFR® 6400 Glove Liner - ANSI Cut Level 5 - 12 Each Pack

    Banom® CFR® 6400 Glove Liner - ANSI Cut Level 5 - 12 Each Pack

    12 Pack at $11.48 each.

    Banom® CFR® liners are designed for use in the food service and steel mills where cut resistance is required, but hands may be exposed to heat or flame. Filament Kevlar® does not meet FDA requirements for food contact so a cover glove must be used. These gloves are not designed for use near rotating or serrated blades. This product should be application tested prior to approval for use. Learn More
  10. Actifit® - ArmorPlate® with Foam Nitrile Fully Coated 10 Inch - ANSI/ISEA 105-2016 Level A4 - 6 Dozen Case

    Actifit® - ArmorPlate® with Foam Nitrile Fully Coated 10 Inch - ANSI/ISEA 105-2016 Level A4 - 6 Dozen Case

    6 Dozen Case at $9.74 a pair.

    Style 2005 Actifit® cut-resistant gloves are the light weight, flexible, and a provide dexterity and tactile feel. Applications include warehouse and fulfillment centers where dexterity and a positive grip are required to handle multiple parts and objects and knives may be used to cut cartons open. Style 2010 is a fully coated 10 inch cut-resistant glove(A4) designed for use in liquid applications where dexterity and a good grip are needed. Applications include engine assembly, machining of aircraft parts, and small sheet metal assembly in areas with plentiful lubricants where increased dexterity is required. Both gloves are nitrile coated on ArmorPlate®. ArmorPlate® is non-conductive and non-friable so it is an excellent replacement for the stainless steel and glass components found in other gloves. Due to their tacky grip, these gloves are not recommended for use when turning nuts, bolts, or screws with a power tool as this can result in a "wrap-up". These gloves are made with a synthetic yarn, so they should not be used near heat or open flame. Nitrile coatings can become slippery in water-based solutions. Both Actifit® gloves should be edge-tested prior to approval for use. Learn More

Items 1 to 10 of 15 total

per page
Page:
  1. 1
  2. 2

List  Grid 

Set Descending Direction